Weboldalunk használatával jóváhagyja a cookie-k használatát a Cookie-kkal kapcsolatos irányelv értelmében.
Menu

GEP-STABLE PRO F7 DUAL BL32 35A (FC+ESC+VTX)

Price:
181.97 EUR
153.13 EUR
Discount: 28.84 EUR
Discount: 16%
Manufacturer:
Model: GEP-STABLE-PROF7_35A_STACK
Qty:pc

Description

After four months of hard work, DUAL ICM 20689 gyroscope both work at the same time,The new F4 Mini 20X20mm Important to release.

There are three versions. We strongly recommend the F7 Dual ICM20689 version, which is a one-off improvement.

Version as follows,STABLE V2 F4 30A(BLS 30A+F4+5.8G 600mw ),STABLE V2 F4 BL32 30A (BL32 35A+F4+5.8g 600mw),STABLE PRO F7 DUAL BL32 35A (BL32 35A+F7 DUAL ICM20689+5.8g 600mw), Pilots can choose as needed.

All three versions have a common feature that maximizes the minimalist layout structure, Highly integrated FPV required functions, perfect clean video output.

The blackbox is integrated with 32 MB flash memory, Export blackbox data, convenient debugging analysis, optimize flight.

Innovative soft damping design to reduce flight control and gyroscope noise and reduce motor heat output

Parameters

Antenna connector MMCX
Dimensions (Length * Width * Height) 26 x 26 x 21 mm
ESC CPU STM32FO51K86(32bit 48mHz)
ESC firmware BLHeli 32
barometer no
BEC 5V/3A
Black box internal 32MB
FC CPU STM32F722 RET6
DJI HD support no
OSD yes
Internal microphone no
Mounting pattern 20x20 mm (micro)
IMU MPU6000
Radio frequency 5.8 GHz
Steady current 35 A
VTX control tramp telemetry
voltage 2-6 cell (7.4V-22.2V)
Weight 16,5 g
STABLE PRO F7 Flight Controller Specs:
MCU STM32F722RET6
IMU 2x ICM20689(SPI)
BlackBox 32Mb onboard Flash
OSD BetaFlight OSD w/ AT7456E chip
Baro NO
BEC Output 5V@3A
Integrated LC Filter
Input Voltage 2-6S Lipo
Firmware target EXF722DUAL
Size 26x26mm board, 20mm mounting holes (M2)
STABLE PRO F7 ESC BL32 2-6S 4in1 Specs:
MCU STM32F051
Input 2-6s lipo
Constant 35Amps
Burst 45Amps
Dimensions 31*31mm(including the power pads)
Mounting Holes 20*20mm,M2
Supports Dshot1200,Proshot,Oneshot,Multishot
Current meter Yes
Target GEPRC-BL32-4IN1
STABLE PRO F7 5.8g 600mW VTX Specs
Input voltage 5V
Channel 48
Power transmission 0mW(Pit mode) / 25mW / 100mW / 200mW / 400mW/ 600mW
Size 24 * 26 mm
Mounting Holes Dimension 20mm x 20mm
Connector type MMCX Connector
BEC Output:5V/1A for Camera of FC
Weight 2.3g
Protocol IRC Tramp

Package contents

– 1 x F4 Flight Controller
– 1 x BLheli_32 35A 2-6S ESC
– 1 x 5.8g 600mW VTX
– 1 x Antenna
– 1 x Capacitance

Reviews

5.00
2 rating
5
(2)
4
(0)
3
(0)
2
(0)
1
(0)
Write a review!
| 5 out of 5 Stars!
Verified purchase
22/01/2023
Hozzá kell tenni, hogy nagyon amatőr vagyok, és jelenleg kint havazik, ezért csak beforrasztottam és beállítottam. Forrasztás ügyileg nagyon előnyös, oldalra kihozott nagy forpaddal az rx tx stb. Amin meglepődtem a betaflight-ban, hogy alapból nem látja a vtx részét, aztán rájöttem talán nem is kell, mert teljesen manuális. Viszont helyette megjelent ami nekem új, a verseny jeladó, ha jól értelmezem. Eddig csak dicsérni tudom, ajánlom, ha még nem is a legolcsóbb.
I should add that I'm very amateur and it's snowing outside right now, so I just soldered it in and set it up. Soldering is very advantageous in terms of the rx tx etc. What I was surprised about in betaflight is that it doesn't see the vtx part by default, then I realized maybe it doesn't need to, because it's completely manual. However, instead, something new appeared for me, the signal of competition, if I understand it correctly. So far I can only praise it, I recommend it, even if it is not the cheapest
| 5 out of 5 Stars!
Verified purchase
03/01/2021
Jó termék korrekt áron.