Weboldalunk használatával jóváhagyja a cookie-k használatát a Cookie-kkal kapcsolatos irányelv értelmében.
Menu

SpeedyBee F405 Mini BLS 35A 20x20 Stack

Price:
76.97 EUR
Manufacturer:
Model: SB-F4MINI-STACK
Qty:pc

Description

The SpeedyBee F405 Mini BLS 35A 20×20 Stack features an upgraded F405 flight controller chip and a built-in Bluetooth chip for seamless wireless Betaflight tuning. This board comes with a 4-level battery voltage display and a built-in barometer and supports connectivity to all DJI Air Units. It offers 4 available UART ports, and a dual BEC setup with 5V 2A and 9V 3A outputs.

The 35A 4-in-1 BLHeli_S Mini ESC provides four synchronized outputs with a continuous current of 35A, delivering strong power to drive all 2-4 inch and lightweight 5-inch quadcopters via a 4-6S battery. Equipped with a TVS transient suppression diode onboard, it better absorbs surge voltage, providing enhanced protection for the ESC.

Features

  • TVS transient suppression diode for surge voltage absorption and enhanced protection 
  • Compatibility with 2-4 inch and lightweight 5-inch quadcopters
  • Four synchronized outputs with a continuous current of 35A
  • Dual BEC setup: 5V 2A output and 9V 3A output
  • Built-in Bluetooth chip for wireless Betaflight tuning
  • Supports connectivity to all DJI Air Units
  • Upgraded F405 flight controller chip
  • 4-level battery voltage display
  • 35A continuous current output
  • Supports 4-6S battery
  • 4 available UART ports
  • Built-in barometer

Specifications

SPEEDYBEE F405 V3 20X20 FLIGHT CONTROLLER

  • DJI Air Unit Compatibility: Compatible with all DJI Air Units (DJI O3/RunCam Link/Caddx Vista/DJI Air Unit V1). Use specific solder pads for pin-to-pin connection. Note: UART1 is used for OSD and SUBS(R2) is used for SBUS receiver signal input
  • BLE Bluetooth: Supported. Used to connect with the SpeedyBee App for flight controller and ESC parameter configuration. Note: MSP switch on UART 4 must be turned on and set to a baud rate of 115200 for Bluetooth functionality
  • Wireless FC Firmware Flashing: NOT Supported. Connect to Betaflight configurator on PC for firmware update
  • Wireless Blackbox Download & Analysis: NOT Supported. Connect to Betaflight configurator on PC for blackbox analysis
  • Current Sensor Input: Supported. For SpeedyBee BLS 35A V2 ESC, set Scale=250 and Offset=-500
  • Power Input: 3-6S LiPo. Powered through 8pin harness G, V wires or G, V pads from bottom side
  • BOOT Button: Supported. Forces FC to enter DFU mode for firmware flashing
  • 3.3V Output: Supported. Designed for 3.3V input receivers. Up to 500mA current load
  • 4.5V Output: Supported. Designed for radio receiver and GPS module. Up to 1A current load
  • Mounting: 20 x 20mm, 3.5mm hole diameter. Compatible with M2 and M3 screws/Silicone grommets
  • I2C: Supported. DA & CL pads on the front side for magnetometer, sonar, etc
  • Traditional Betaflight LED Pad: Supported. Used for WS2812 LEDs
  • Supported Flight Controller Firmware: BetaFlight (Default), INAV
  • BetaFlight Camera Control Pad: Yes. CC pad on the front side
  • ESC Signal: M1 - M4 wires or soldering pads on the bottom side
  • UART: 6 sets. UART1-6 with dedicated purposes
  • Firmware Target Name: SPEEDYBEEF405MINI
  • Buzzer: BZ+ and BZ- pad used for 5V Buzzer
  • 5V Output: 4 groups. The total current load is 2A
  • 9V Output: 1 group. The total current load is 3A
  • DJI Air Unit Connection Way: Direct soldering
  • Dimension: 30(L) x 32(W) x 7.8(H)mm
  • Smart Port / F.Port: Not Supported
  • ESC Telemetry: UART R5 (UART5)
  • Blackbox: 8MB Onboard Flash
  • RSSI Input: Not Supported
  • OSD Chip: AT7456E chip
  • IMU(Gyro): ICM42688P
  • USB Port Type: Type-C.
  • WIFI: Not supported
  • Barometer: Built-in
  • MCU: STM32F405
  • Weight: 9.6g

SPEEDYBEE 35A BLHELI_s MINI V2 4-IN-1 ESC

  •  Mounting: 20 x 20mm ∅3.5mm hole size, compatible with M2 and M3 screws/Silicone grommets
  • Power Output: VBAT (Battery voltage, used to power the flight controller)
  • Current Sensor: Support (Scale=250 Offset=-500)
  • ESC Telemetry: Not supported
  • Burst Current: 45A (5 seconds)
  • Dimension: 35 * 35 * 5.5mm
  • ESC Protocol: DSHOT300/600
  • Continuous Current: 35A * 4
  • Firmware: BLHeli_S J-H-40
  • Power Input: 3-6S LiPo
  • Weight: 7.2g

Parameters

ESC firmware BLHeli S
Black box internal 8MB
FC CPU STM32F405
DJI HD support yes
OSD yes
UARTS 6
Mounting pattern 20x20 mm (micro)
Steady current 35 A
voltage 3-6 cell (11.1V-22.2V)

Package included

1x SpeedyBee F405 V3 20x20 Flight Controller

1x SpeedyBee 35A BLHeli_S Mini V2 4-in-1 ESC

5x M2 Silicone O-Ring

5x M5 Silicone O-Ring

5x M2 Anti Vibration Silicone Grommets

5x M3 Anti Vibration Silicone Grommets

1x 8-Pin JST cable 30mm

1x 35V 470uf Capacitor

Reviews

There are no reviews for this product.
Write a review!